BORE ACE 打檔輔助桿 (BOER ACE 前齒盤外蓋對應)
Installed on my 2012 SR400FI with the Collar Set.The description says no modification, but you need to modify the Boots at the back of the Change Pedal. (You just need to cut the tube of the Rubber, s...
Installed on my 2012 SR400FI with the Collar Set.The description says no modification, but you need to modify the Boots at the back of the Change Pedal. (You just need to cut the tube of the Rubber, s...
At first I considered the Manufacturer's Oil cooler here. But recently, I thought it was a little too large because I'm running slowly.Then I saw the Heat Radiation Fin for Oil TankDown tube in the Ma...
First of all, it's expensive! 6,000 for all these Parts …Secondly, the installation instructions are unfriendly.The Instruction Manual that came with the Change Accent itself was Only if the Sprocket ...
Not too soft, not too hard, and the design is simple and cool I went Touring and the Grip is good, it absorbs vibrations reasonably well, and the wrist I wasn't even tired 。 I finally found the Grip I...
I was a little reluctant to use Shift because of the old model, but after I installed this product, it's been a little tougher Chica Chi is now entering It's an inconspicuous part, but I highly recomm...
The manufacturer's Negative Pressure Adapter to this product The installation is very easy because of the Bolt On However, when 1 pc of an attached bolt is tightened about halfway, it suddenly becomes...
Because the OEMs turn the hex heads, there will inevitably be scratches from the opening and closing in the visible areas, but the bore Ace's is a hexagon of holes so you can't see the scratchesThe ri...
It is a fin for better heat dissipation of the Camshaft CoverTo install the Heat Radiation FinBody, remove the Porto and Pipe and Just insert it into the Camshaft Cover from the side, fit the Pipe and...
Although installation is possible without taking down the tank, it is Large strange to put in L-TypeWrench I struggle withThe Short Neck L-TypeWrench makes installation quite easyI bought it for the m...
If there is enough skill to remove Normal cab, it will easily take youNegative pressure is explained to be connected to Fuel Cock, but I dared to connect to Air inductorSince there is no choice, Fuel ...
Until then, I was using 60 mm Funnel for FCR Carburetor Body 41, but I did not feel the explosion I felt at the time of SCRUp + High Camshaft FCR Carburetor Body 35 I was using at the beginning 'W...
Until just before installation, there was a doubt - - -I was betrayed in a good way.Torque up. definitely.After all, Manufacturer doing seriously is different ~Number of boa Ace products handledI want...
No one notices it, but I really like it.I did mirror surface processing myself.The mixture became thinner than originally, but the amount of air is increasing by that amount.You can blow better than t...
It is dramatically good. After exchange, since an air-fuel mixture becomes thin, change of setting is needed in the direction of deep Sakka. if setting is decided -- Power -- it can blow and stage fri...
Parts that flow of the air-fuel mixture from a carburetor to an engine will be made into a smooth. It is the feature to carry out elliptic cutting of the admission port, and also it is aiming at the f...
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING