MINIMOTO 儀表橡膠墊 梯型
I was worried about the wiring behind the Headlight because rainwater gets between the Meter and the LightHouse, I looked for an OEM Product but couldn't find one and this product was very helpful.
 |  |  |
| | | |
 |  |  |
| | | |
 |  |  |
| | | |
 | ||
| |
MINIMOTO 鏈條定位工具
The Ninja 1000's Chain pull is Eccentric, so it's not that much of a Quantity:Pair (for Left and Right) I thought I wouldn't go crazy withAfter using this product, I knew I wasn't crazy.I'm happy with...
MINIMOTO 燃料油箱 安裝橡膠和襯套 1台份
It is a part that is hidden in the tank, so I personally think it is possible to use Other Brand Product.Best of all, the prices are reasonable!
MINIMOTO MINIMOTO SUPER 高角度凸輪軸 (TM-1)
The top of Cam's mountain was angular, so I polished it with oil stone. The effect is that the carburetor with VM16 has fattened up the Torque above the mid speed range. It doesn't mean that I can cli...
MINIMOTO 6V 頭燈燈泡(透明單顆)
Since 6v bulbs are hard to come by.It's helpfulIt is safe to have it as a spare.
MINIMOTO MONKEY DAX 鋁合金製 鏈條調整器
I thought I could install it right away, so I pulled out the Axle Bolt without curing the wheel. When I installed the AxleBolt, I found that the Ring part of the Chain Adjuster was too thick and the A...
MINIMOTO Monkey 前叉HONDA標誌 (大)＆支架
My GORILLA has a carrier for the front basket, so I used a hexagonal spacer to lower it by 20mm.
 | |  |
| | | |
 | |  |
| | | |
 |  | |
| | |
MINIMOTO Universal Foldable Aluminum Slope (Long) ...
I used to use a thick wooden board for Motocross practice, but after hard practice, it was quite hard to load. It's foldable, so it's not too bulky to load in the car, and it's very easy to use. I'm n...
MINIMOTO Z50J/DAX II型 前輪轂用 輪軸
I used it for my MONKEY.Nothing different from OEM. I have no complaints. If I had to say, I think the surface treatment is a little cheap, but I haven't seen any rust floating around after 6 months o...
MINIMOTO High Type 進氣歧管
MINIMOTO's PC20 Same SizeCarburetor (https://www.webike.net/sd/23872858/)Also MINIMOTO's Monkey Type Z Full Kit 88cc Type S Cylinder (https://www.webike.net/sd/23872950/)We have installed this kit on ...
MINIMOTO Aluminum Slope for Motorcycle
It's made of aluminum and is lightweight, making it easy to use.
MINIMOTO 後駐車架 (適用12-21吋輪框)
I know it's a series of pitches, but I installed the RIDEA RIDEA Stand Hook yesterday and used it with a U-shaped hook.It's more obvious than Swing ArmType, but it's totally stable.However, it interfe...
MINIMOTO Universal Foldable Aluminum Slope (Long) ...
I was looking for a Ladder to load my kid's QR on the Land Cruiser 60.We decided that it was too tough to lift up on a car that was lifting up, so we bought this one.First of all, Cost performance is ...
MINIMOTO 後駐車架 (適用12-21吋輪框)
I bought it for the MONKEY125.First of all, one hole in the Button bolt with a hole to stop the Tire was filled in.I managed to install it with Pliers across the head.I didn't have a Stand Hook, so I ...
MINIMOTO Mini保養用 後駐車架
The picture is a lifted state with MONKEY8InchSpec.The Tire is about 10cm up.It's stable enough for lightweight vehicles and easy maintenance.
 |  |  |
| | | |
 | |  |
| | | |
 |  | |
| | | |
 |  |  |
| | | |
 | |  |
| | | |
 |  |  |
| | | |
 |  |  |
| | | |
 | ||
| |
MINIMOTO 卡鉗活塞固定鉗
It is not possible to hold the piston with grip strength alone when removing a stuck piston.Even if you wrap Towel around it, your hands will hurt.You might like Stopper included. which is a little ab...
MINIMOTO 廢油盤／廢油收集容器型(機油更換用)
When I loosen the drain bolt to drain the oil, if I don't collect the bolt well, the bolt will fall into the hole to collect the oil like a cartoon. It was not possible to collect Bolts with disposabl...
MINIMOTO 活塞環壓縮工具
First time I've used it.It seems like a lie that it used to take me about 30 minutes to push it in with my fingers.The instruction manual is not included, so the first time user may fit it upside down...
MINIMOTO 把手管材鑽孔夾具
I used it only once to drill a hole in my HURRICANEHandlebar, and had no problems.
MINIMOTO 通用型 前叉油面調整工具
I was able to use it without any problems. It was easy to use even for an amateur because it didn't require much effort to suck out.
MINIMOTO 卡鉗活塞固定鉗
Used for Caliper piston rub.It is impossible to pull out the piston without this, unless the piston is in a good mood right after assembly.There was no hesitation in using it, and it was strong enough...
MINIMOTO 鎖緊螺帽多功能鉤形扳手
[How is it used?I use this product to change the hardness of the Rear shock on my two Motorcycles. I bought two of these products.Was the one you received as per Image?ImageHow was your experience wit...
MINIMOTO 洩油螺絲墊片 M12
Material:I bought it because it was slightly cheaper than Aluminum.It's a normal drain washer, no oil leaks, and it works great.Since the engine is blacked out, I thought it would be a good color to a...
MINIMOTO 鎖緊螺帽多功能鉤形扳手
I bought this because I needed it to remove the Stem when I repainted the Frame.The deciding factor in the purchaseI was not sure of the size, so I bought it because it was a wide Hook wrench with som...
MINIMOTO 卡鉗活塞固定鉗
Function and workability are fine, butThe part that suppresses Piston is Knurl by the genus Gold, so it scratches the inside of Piston.If you are worried about it, you need to take measures such as pu...
?
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING