擺臂重量:正常情況下3.5kg至1.8kg(對於格羅姆`三平方`+0cm)
擺臂采用7n01鋁材,1.8kg,而原廠擺臂為3.5kg,重量輕,剛性強。更輕的重量提高了摩托車的操控性。
選項
【搖臂處理】
.黑色陽極氧化處理(gCraft部件號:60198)+25,000日元
。Cerakote Finish (gCraft #60807) +30000日元
【什么是Cerakote?】
CeraCoat是目前美軍使用的一種特殊烤漆。
經測試,該塗料能應對惡劣的環境,在開發過程中注重 "耐熱性"、"耐磨性"、"耐久性"、"散熱性 "和 "絕緣性"。
陶瓷材料經專用機器粉碎後,混入塗料中,以提高漆膜的強度。這使表面呈現出類似珍珠皮的光澤,但塗層可以很薄(25微米)
焊接痕跡(珠子)可以不被隱藏地留在表面。
這種表面的附着力在所有塗層材料中是最高的,即使彎曲也不會起皺,即使是踏石也不容易掉漆,所以適合 "框架 "擺臂。
*正常交貨時間為3-5周。
【方案1】【方案1】鏈條滑塊用螺栓固定(gCraft零件號:60228)+1000日元
將鏈條滑塊由鉚接改為螺栓固定。磨損後容易更換。
【方案2】【方案2】樞軸部滾針軸承型(gCraft No.60192)+3000日元
標准型將軸套的樞軸部改為滾針軸承。
更耐用,運行更平穩。
【選購件3】立鉤底座(m6)(gCraft部件號60903)+3000日元
可在底座上安裝gCraft立鉤或外置立鉤(m6)。
【方案4】拉鏈方案
。賽車立鉤(gCraft部件號:60186)+3000日元
這是為了將鏈條的後端轉換為立鉤。gCraft部件號:32071.32072.32073賽車立鉤可以安裝。
*不能與G-craft零件號:33170ap洛克希德卡鉗支架一起安裝(它會干擾)
。後拉式(gCraft部件號:60221)+3000日元
後拉式調節器的設計,消除了鏈條調節的麻煩。
*不能安裝在 "ow型"(g-craft部件號:60014)+3000日元
*不能安裝在 "ow型"(g-craft部件號:60014)。通過錐形拉鏈器,消除了軸軸的垂直運動。
錐形面板移動,防止垂直運動。這種機構也被用在大自行車的擺臂上。
ow型賽車立鉤(gCraft編號:60188)+5000日元
ow型鏈拉背面改為立鉤。
您可以將G-craft零件號:32071.32072.32073的賽車架掛鉤連接起來。
*不能與G-craft零件號:33170ap洛克希德卡鉗支架一起安裝(它會干擾)
。偏心式(g-craft零件號:60059)+5000日元
這是川崎摩托車上常用的偏心式拉鏈器。
*只有在使用盤式時,才能使用連接到擺臂底部的卡鉗支架。
Swingarm Weight: Stock 3.5kg→1.8kg (for GROM, triple square, no sway bar, +0cm)
The swingarm is made of aluminum 7N01 material and it is 1.8kg lighter than stock swingarm 3.5kg.
■Option Description
[Swingarm finish]
・Black anodized finish (G-Craft part number: 60198)
・Cerakote finish (G-Craft part number: 60807)
[What is Cerakote?]
Cerakote is a special heat coloring and normal temperature paint manufactured by NIC and currently used by the US military.
It has been inspected to meet the harsh conditions, and has excellent heat resistance, abrasion resistance, durability, solvent resistance, heat dissipation, heat insulation and other performance-oriented research and production.
Ceramic is crushed by a special machine and mixed into the paint to improve the strength of the paint film.Therefore, the surface becomes pear-shaped, but the coating film can be made very thin (25 microns)
Weld marks (beads) can be left on the surface without being hidden.
The adhesion is the highest among all coating materials, and the surface treatment is suitable for frames and swingarms because it does not wrinkle even when bent, and the paint does not peel off easily even by stepping stones.
*Please allow 3 to 5 weeks for normal delivery.
[Option 1] Chain slider bolt fixing specification (G-Craft part number:60228)
Change the chain slider from riveted to bolted.Easy to replace when worn out.
[Option 2] Pivot part needle bearing specification (G-Craft part number: 60192) +3000 yen
The standard is to change the pivot part of the bushing to a needle bearing.
Improved durability and smooth operating characteristics.
[Option 3] Stand hook base (M6) additional processing (G-Craft part number: 60903)
G-Craft stand hook or aftermarket stand hook (M6) can be attached.
[Option 4] Chain adjuster option
・Racing stand hook specification (G-Craft part number: 60186)
The rear part of the conventional chain pull can be used as a stand-hook.G-Craft Part Number: The 32071, 32072 and 32073 racing stand hooks can be installed.
*G Kraft Part Number:33170AP Lockheed caliper support cannot be installed (will interfere)
・Back pull type (G-Craft part number: 60221)
This backward pull adjuster is designed to eliminate the hassle of adjusting the chain.
Since the adjusting nut is located at the end of the swingarm, it is easy to adjust the adjusting part which was difficult to turn due to interference of tools
*Can not be installed on the racing stand hook specification and OW type at the same time
・OW type (G-Craft part number: 60014)
The chain puller is tapered to eliminate vertical misalignment of the axle shaft.
The tapered frame moves so there is no vertical misalignment.This mechanism is also used for swingarms of big bikes.
・OW type racing stand hook specification (G-Craft part number: 60188)
The rear part of OW type chain pull is changed to stand hook specification.
G-Craft Part Number: The 32071, 32072 and 32073 racing stand hooks can be installed.
*G Kraft Part Number:33170AP Lockheed caliper support cannot be installed (will interfere)
・Eccentric type (G-Craft part number: 60059)
This is an eccentric type chain puller commonly found on Kawasaki motorcycles.
*Only caliper supports with calipers attached to the lower part of the swingarm can be used on disc models.