e1型排氣管尾段
Product # S-S13SO2-HRC
Product # S-S13SO2-HRC
※商品不包含圖片中的手把冠座。
※尺寸量測以水平測量。
※圖片僅供參考,圖片可能包含其他顏色或商品。
Model Page Links
Design, texture and construction are all good!
The weight is light and the product precision is perfect.
If you remove the Baffle, the sound is very powerful.
Good sound, not annoying in my opinion.
Full Exhaust System is also available by adding Header.View Detail
Fits: HONDA VFR800F 14-21, HONDA VFR800X 15-16 (ABS)
This is an installation on a VFR800X (2015).
This time I installed an e26 (Slow Veneer with Akrapovic) approved Silencer.
The order was placed via PLOT, but the translation (there is no InstallationGuide to enter here, but it was basically a light maintenance Level that anyone could work with while looking at the pictures.
In Stock condition, it is quieter than OEM thanks to the Inner baffle.
SilencerBody is stamped with Race Use.
The volume becomes small, but the quality of the sound is thick and humid, and it became a crisp sound.
The following is a story from my dream.
As for the Inner baffle, it is fastened from the inside with a Bolt and has welding points.
(Bolt is stuck from the inside of the exhaust port to the outside)
It has a 4mmHex head on the inside of the Bolt, if you know what I'm talking about.
I thought there was a nut in the carbon silencer end that was receiving the Bolt, but the tap was cut on the silencer body side and it seemed to stop at 1 pc of Bolt.
There are various specs on this point, and I've done a lot of research myself, so I hope this information is useful to someone.
The volume in its original form sounds bad at the closing Level.
I'm in a dream.
The overall work is relatively light maintenance Level, but there are two points.
The diameter of the main pipe is quite tight, so I had to push it a little harder to make the connection.
Also, it may not seem necessary to relocate the Center Stand Receiver Rubber, but you should do it properly.
The Rubber relocation may be the hardest part of this installation.
Oh, you'll need Torque's T45 for installation.
Please prepare in advance.View Detail
Fits: BMW R1150GS 99-04, BMW R1150GS 01-06 ADVENTURE
I have a BMW R1150R 2001.
This AXIS Lab Bitch Slip-on Silencer Titanium is for the R1150GS but is completely compatible with the R1150R.
It was installed without any problems.
I have replaced the Catalyzer with a REMUS YPIPE and of course the installation is fine.
By removing the Catalyzer and replacing the Exhaust System, the weight was reduced by 9.1kg.
And the exhaust sound is now nice and dry.
If you would like to replace the AXIS Lab Bitch Exhaust System on your R1150R, please contact us.
G S isView Detail
Fits: KAWASAKI NINJA2 Helmet50RSL 15-17 ABS, KAWASAKI NINJA2 Helmet50RSL 15-17, KAWASAKI Z250SL 15-17 ABS
It seemed to be discontinued, so I searched the world for the last Chance and Motardinn (Spain) Imported from.
I know the sound is bad, but I bought it in Styling only.
sound
It's as quiet as NORMAL.
The White Buy doesn't even look at it for normal driving.
I rarely do AfterFire Ya either.
But after 4,500 rpm, things change.
I didn't get the JMCA, but if you measure it at half of the maximum power rotation, it will pass in plenty of time.
Acceleration noise is not a problem as long as you carry the included certificate as it is an eMark product.
Design
Parenthesis is nice in typical AXIS La Hexagonal.
However, like other products of that time, there is no silencer band or joint spring because of the direct attachment bracket and intermediate pipe, so the race is a little less.
Ends are Material:Carbon and non-removable Baffle welded on.
As for the Baffle, because it is an offence to be able to remove it, this point is no complaint, but the color is the place where I want you to make it Black so that it does not stand out.
color
Material:It's Stainless Steel, but it's blackish rather than silver.
The intermediate pipe directly attached to Silencer is also a beautiful color.
Performance
Compared to the straight WR039;S, it's a little bit milder, but it's easy to handle and torqued fully.
General review
If you want a noisy exhaust system, I wouldn't recommend it, but I think it's a good exhaust system that can run quietly or quickly with a single Axel to match the scene.
If you import it, it's inexpensive, in the low 40,000 yen range, so it's a Recommendation.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
通知
在您加入購物車前請選擇選項。
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.