NR前腳踏桿組
Product # NNR440BK
430.37 ~ HKD (8,320 日幣)
定價 465.54 HKD 节省 最多 8%
+83~ Webike點數 (4.29 HKD)
當訂單成立時,我們將確認製造商的庫存並透過e-mail發送確認出貨時間給您。
Product # NNR440BK
430.37 ~ HKD (8,320 日幣)
定價 465.54 HKD 节省 最多 8%
+83~ Webike點數 (4.29 HKD)
長期使用時,會因為紫外線的影響而褪色,但不會影響產品的功能。
Model Page Links
Fits: KAWASAKI BALIUS , KAWASAKI BALIUS II , KAWASAKI GPZ750 R , KAWASAKI ZR-7 , KAWASAKI GPZ900 R
I chose this color to make it match with BEET rearsets. It doesn't stand out, but looks nice.
In terms of installation, there was no problem and was easy.
If anything, it was hard to take off the fixing clip and to remove the old grease.
It was good because I was given a chance to clean it up.
It would be even better if it was a little bit cheaper.View Detail
Fits: KAWASAKI BALIUS , KAWASAKI BALIUS II , KAWASAKI GPZ750 R , KAWASAKI ZR-7 , KAWASAKI GPZ900 R
Since it is an atmosphere well similar for the product in Back-step attachment, they are purchase and attachment as a Tandem Peg.Although it is a Front-step Peg in Mr.
webike's article category,is it perfect if the size of the Holder of a Tandem step is measured!?
(isn't this an object for Tandems ?) --
> -- if it attaches, a Peg will not have leaped up delicately.A settlement is bad.The portion of R of the root of the
Peg will be equivalent to the angle of a Holder.
It is unavoidable processing.It is failed using a Grinder or a File to delete the portion equivalent to which the
Peg is.
Such small processings are not disagreeable.It being soft and enjoying processing, since the
raw material is an Aluminum, it attaches without it taking 1 hour, and is termination.Suiting the atmosphere of the
Back step well, it is satisfactory.They are a Dress-up parts and the parts for being self-satisfied rather than the
functional part.View Detail
Fits: YAMAHA YZF750 R , YAMAHA YZF600 R , YAMAHA YZF1000 R , YAMAHA XJR1300 , YAMAHA XJR1200
I installed it in the SR 400. However, the positional balance with the Leg guard when folding the footpeg was very bad and it looked like it was completely bad. So I gave up the installation and put it back in the OEM. It was a waste..View Detail
For the introduction of Striker's Rear Sets, Tandem Footpeg's Peg also purchased to match a similar shape.
?Good point?
- It's all black so it gets tightened
- Non-slip processing can be done without complaint
?I like it?
- At least I wanted a Slider-like lid at the tip of Peg
- Inside Package footpeg Peg rubbed each other and Anodized was partly scraped
- It is universal because it is universal product but footpeg Peg does not go down
There is no MT-09 in the compatible model, but OEMTandem FootpegPeg of FZ-1 FAZER was the same as ProductNo so I purchased it with self-responsibility.
Since the bottom of MT-09's Frame is split and black feeling black, I think that the combination of Rear Sets of Black and Tandem Footpeg Peg has resulted in a sense of unity with Large.
With regard to installation, removing the split Pin and removal of the old Grease is awkward, but even a 100 Level tool can be replaced satisfactorily.
It is a pity that the tip part is empty, so when you look at it from the top in a folded state, the inside Bolt looks like it is visible, and you need to be careful not to get dirty when riding in the rain or car wash. It would have been good if the lid like Slider like Rear Sets' Peg was attached at least ....
It is doubtful that the way of packaging is large.
Material : Peg is casually contained in the plastic package of Plastic, so it rubs with vibration during transportation and some Anodized was peeling off. Small I will not tell you to split up, but at least I wanted you to wrap it with Vinyl or something.
As it is with Yamaha car's Universal Product it is difficult to install perfectly with a ponding like OEMParts.
The footpeg did not go down as my Spring hole was slightly different in my MT-09.
Perhaps I think that if you cut down a few millimeters of Spring-crafted Washer, I think it will go down, but since there are no particular problems in the folded state, I'm thinking to process Washer as if it can go down.
Rear Sets If you are equipped with cars you are definitely wearing a place to wear, but the price is high for finished finish, so it is true that you want to study a little more.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
通知
在您加入購物車前請選擇選項。
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.