材質:鋁合金
【套件內容】
・加寬後搖臂(附平衡架+16cm)
・3件式10吋5.5J輪框
・加寬輪轂
・煞車系統
・前齒盤 偏移系統
・加寬避震器吊架
【安裝】
套件中不包括固定後制動總缸的支架。請另行准備。對於驅動鏈輪偏移組件,你需要拆除發電機蓋的鏈輪部分。另外,它還能兼容日系和隆鑫的發動機,但一些中國的發動機,如150cc的力帆發動機可能在4個點上無法支持。
你必須使用420尺寸的鏈輪作為前後輪。附上裝配說明。參照說明書仔細組裝。但是,維修工作的常識技術在手冊中並沒有提及。我們需要一個有摩托車維修經驗的人做組裝工作。傳動鏈架的數量根據客戶的車況和前後鏈輪的情況而不同,所以gm-moto不提供這方面的信息。
即使後懸架處於全底狀態,開車前也一定要檢查是否有異常的接觸點。如果車架與擺臂之間的間隙每邊超過0.5mm,請使用墊圈減小間隙。如果樞軸緊固時間隙過大,擺臂就會過載,最嚴重時可能會損壞。開車後,要注意 "初始松動",經常檢查車輛,避免出現意外問題。
【保修】
請注意,由於運輸問題,可能會出現輕微的劃痕和擦傷。我們對產品不作保證,除非是嚴重損害其價值或功能的缺陷。安裝後不接受任何理由的退貨。此外,開始行駛後出現的問題,往往是由於行駛與保養條件或車況不匹配造成的。
*鏈條調節器和支架掛鉤的顏色由金色改為鈦色。
Material: Aluminum
[Kit Contents]
・Wide swingarm (with stabilizer +16cm)
・3-piece 10-inch 5.5J wheels
・Wide hub
・Brake system
・Drive sprocket offset system
・Wide suspension hanger
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
[About the installation]
The rear brake master cylinder fixing bracket is not included in the kit.Please prepare separately.The drive sprocket offset kit requires the sprocket section of the generator cover to be cut off.However, some Chinese engines such as Lifan 150cc may not be able to support 4 points.
Please use the 420 size sprockets for Monkey.Assembly instructions will be included.Please refer to the instruction manual and assemble carefully.However, common sense techniques for maintenance work are not described in the manual.Experienced motorcycle mechanics are required to perform the assembly work.The number of frames of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
Even when the rear suspension is at full bottom, be sure to check for any abnormal contact points before driving.If there is a gap of 0.5mm or more between the frame and the swingarm, please use washers to reduce the gap.If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.After the start of driving, pay attention to the occurrence of so-called "initial loosening" and perform frequent inspections to prevent unexpected problems.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.
※The chain adjuster and the stand hook have been changed from gold to titanium color.
*There may be changes in product specifications due to the manufacturer's reasons.