- 改裝零件
- 排氣系統(排氣喉)
- 排氣管尾段(排氣喉)
- NOJIMA
- NOJIMA - 排氣管尾段(排氣喉)
- 商品列表
- Vintage megaphone 電鍍排氣管尾段 (附標誌)
Vintage megaphone 電鍍排氣管尾段 (附標誌)
Product # NMS220SMCE
3,210.84 HKD (62,100 日幣)
定價 3,210.84 HKD 节省 0%
+621 Webike點數 (32.1 HKD)
Product # NMS220SMCE
3,210.84 HKD (62,100 日幣)
定價 3,210.84 HKD 节省 0%
+621 Webike點數 (32.1 HKD)
Model Page Links
I'm using it with SR400 model 3 NORMAL
As described in the Construction Manual, we have assumed a NORMAL state Since this is an Exhaust System, this is a review in a NORMAL state
Yes, installation
Because of Slip-on Silencer and SR400Exclusive Design, it is an amateur But it was easy to install
The Center stand stopper is included, but the Exhaust Joint Gasket must be purchased separately
Fat Style
I arrived at this exhaust system because I like the look of NORMAL
So much for the many SR400's customized exhaust systems I don't think there are many exhaust systems that look close to the NORMAL Because it does not break down the style/balance of NORMAL in a large way, it has a very good impression It is
Also, the exhaust system's plating process is very clean and It's also a good place to be
"Ding dong
As for the volume, naturally it becomes Large, but it is too much annoying for JMCA Correspondence I like the non-threatening volume that does not intimidate people The sound pressure is increased and the sound is crisp and clear
The sound quality is like a single cylinder without any vulgarity However, the sound of AfterFire is also combined with Large sound
Personally, I'd rather hit the air than the Parisian high notes of Cabtonetc I like the thudding bass, so I like this one too
◯Power
Idling to 2500 torque-turns will drop to the extent that even a layman can understand I think the reason for this is that the torque is better, but the so-called "single cylinder torque" feeling is The direction of decrease
Because of the reduction in torque at low RPMs, the way you drive with the low RPM torques that are used so much in SR It will be difficult
For example, when turning the Axel as it is at 40km/h in 5th gear, the OEMs "Tot-tot-tot And it accelerates, but this one is "T-t-t-t-t-t and the Power will be a delayed Image
In this case, I think it would be better to drop down to 4th gear and re-accelerate
Also, the start-up is obviously slower than the OEM
In other words, because the TorqueBand changes to a higher RPM range than at OEM You will need to run peaked
Fatigue mileage
Depending on how you run it, if you run it the same way as you did at OEM, it will be about the same
◯General Comments
I hadn't run the Engine on the SR until now, but this Exhaust I found the joy of running the Engine in the System
A realm of strength that feels good has changed to a higher rpm than the OEM, so if you maintain that power band while running It's very enjoyable It comes with a pleasant sound at the same time
After all, even at Slip-on Silencer, the manufacturer who is good at Race You can feel that this is an Exhaust System
It's a slip-on silencer, so you can easily change it to suit your riding style and purpose I think it's good
Manufacturer also wrote Large people should not be ashamed of their style and sound I think it is an exhaust system that makes the
The OEM sound is a bit underwhelming "Large people" to RecommendationView Detail
It was quite excited by exchanging the first Exhaust System and made this Exhaust System exclusive for SR 400. Although it is the result attached at NORMALCarburetor setting... Obviously the power of acceleration has increased and the sound has also become quite sound and crisp sound with JMCA Certified but at the same time its startability is not bad at all. However, there is a possibility that Cancellation of air induction should not be done, so After Fire will repeat at Large volume.
Regarding the installation itself of the Exhaust System itself, I will not mistake it with a polite instruction manual first, remove the Rubber part of OEMExhaust System Bracket and Center stand stopper and reuse it. The difficult point here comes with the Bracket of the Center stand stopper, but when you attach the Rubber part of Stopper to this Bracket, it is hard to work hard. Please note that you can not attach the center stand stopper unless you remove the gold tool of the OEMExhaust System mounting Bolt hole located just under the Motorcycle Body even if it is attached to the Stopper from the root together with the Pin..
Exhaust Gasket should also purchase things in the item column at the same time.
Although I wrote variously, this Slip - on Silencer, which was created on the premise that Nojima will attach to NORMALSR will make SR a more attractive Motorcycle. It is exciting system to ride, have fun, look beautiful, listen and excited!View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
通知
在您加入購物車前請選擇選項。
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.