駐車球
Product # E012BOY0013
297.43 HKD (5,750 日幣)
定價 377.61 HKD 节省 21%
+58 Webike點數 (3 HKD)
匹配
- Z1000 (water-cooled)14
- NINJA1000 (Z1000SX)14
- Z80013-
Product # E012BOY0013
297.43 HKD (5,750 日幣)
定價 377.61 HKD 节省 21%
+58 Webike點數 (3 HKD)
匹配
附帶保護裝置
【規格】M8
【數量】適用一台車
※基於安全考量,駐車時,必須有兩個人在場。
※支架的V形立鉤部分可能會損壞到搖臂。
※立鉤可能會干擾到排氣管,因此請從車輛上移除立鉤,但駐車時不在此限。
Model Page Links
Fits: KAWASAKI NINJA1000 (Z1000SX) 14, KAWASAKI Z800 13-, KAWASAKI Z1000 (water-cooled) 14
Purchased as OEMStand Hook for NINJA1000 (Both SidesExhaust System).
It is a US Kawasaki and the instruction manual is only available in English version, but it can be installed in less than 30 minutes.
I use a J−TRIP rear stand, but the Exhaust System and VHook fight with each other.
The gap between the Exhaust System and Stand Hook is small (Quantity to be exact).:Pair (for Left and Right) The VHook hits the Exhaust Guard (in my case it's the Left Side).
I thought about Cut of Exhaust Guard, but I use L-Type receiver for Rear stand.
I think the One SideExhaust System is Large strong?
Now I have it installed as a decoration because it looks good.
The price is high for the thing.View Detail
Fits: KAWASAKI NINJA1000 (Z1000SX) 14, KAWASAKI Z800 13-, KAWASAKI Z1000 (water-cooled) 14
Original OEMParts from US kawasaki.
I don't know if it's because Kawasaki in Japan doesn't carry them or not, but the webike compatibility chart hasn't been updated at all.
If you can use M8 Stand Hook, it will fit, but you can check US kawasaki Site if you are interested.
As a product, Material:Bobbin and Material in Stainless Steel:Aluminum Protectordisc (with Logo) The combination of the two.
Protectordisc is somewhat matted and has a sense of unity with the Swing Arm.
On the downside, it's expensive.
If you want to buy only Bobbin, you can buy it for half the price of this Parts. If you don't care about it, you can buy it there.View Detail
Fits: KAWASAKI NINJA1000 (Z1000SX) 14, KAWASAKI Z800 13-, KAWASAKI Z1000 (water-cooled) 14
The Swing Arm has the Stand Hook mounting holes, but for some reason the Ninja 650 is not included in the Kawasaki OEM Stand Hook.
I bought the other sizes for vehicles that fit the mounting holes of the Swing Arm and tried to install them.
When the maintenance stand was used afterwards, there was not even a thing that was scratched on the body of the car.......but when I ran around the neighborhood a little after maintenance and touched the part to check the looseness of the Mounting Bolt, the exhaust hit or it was quite hot!
There was a good reason why it wasn't in the compliant models.
The resin part might melt if you run for a long time in Touring, etc., so I remove it except when using STAND. 。
View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
通知
在您加入購物車前請選擇選項。
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.