- 改裝零件
- 煞車系統
- 煞車皮(來令片)(迫力皮)
- RK
- RK - 煞車皮(來令片)(迫力皮)
- 商品列表
- Fine Alloy 55 煞車來令片
Fine Alloy 55 煞車來令片
Product # 914FA5
匹配
- CBR250R (2011-)11-17
- Rebel 50011-17
- GSR25012-16
- Z80013-16
- VERSYS 65015-20
Product # 914FA5
匹配
Model Page Links
Fits: HONDA CRM50 88-92 [Position/Number of discs] Front/Single disc [Compatibility, HONDA CRM80 86-91 [Position/Number of discs]Front/Single disc [Compatibility]◎, HONDA CRM50 93-99 [Position/Number of discs] Front/Single disc [Compatibility, HONDA CBX125 82-84 TS/GD [Position/Number of discs] Front/Single disc [Compatibility]○ ○, HONDA CG125 04-08 [Position/Number of discs] Front/Single disc [Goodness of fitment
[How is it used?
Front disc brake was replaced to improve its effectiveness.
How was your experience with it?
Braking power was not a good result.
How did it compare to other products?
It works better than NORMAL, but DAYTONA's Red Pad works better.
I think this one is more durable.
[Points to note]
Be careful not to get oil on the surface when installing the unit.View Detail
Fits: HONDA FTR250 86 /II [Application Areas/Number of Discs]Front/Single Disc [Compatibility]◎, HONDA FTR223 00-15 [Place of use/Number of discs]Front/Single disc [Compatibility]○ ○, HONDA CB223S 08-15 [Position/Number of discs]Front/Single disc [Goodness of fitment]◎, HONDA CB250RS 85 [part used/number of discs] Front/single disc [degree of fitment, SUZUKI SKYWAVE400 burgman 99 AN400X [part used]Rear [fitment]◎
[How is it used?
Exchanged.
Was the installation difficult?
I did not do it alone because it is a life-threatening part around the Brake, but installed it with a skilled person.
How was your experience with it?
I was a little worried about the effectiveness at the beginning of the run, but after a few kilometers, my worries were gone!
I had no problems on my recent touring trip!View Detail
Fits: DERBI Terra125 07-14 [Position/Number of discs] Front/Single disc [Goodness of fitment, HONDA CRF250M 12-15 [Position/Number of discs] Front/Single disc [Goodness of fitment, HONDA CRF250L 12-15 [Position/Number of discs] Front/Single disc [Goodness of fitment, DERBI CROSSCity 125 (07 - 14) Application Area/Number of Discs]Front/Single Disc [Compatibility]◎, DERBI Mulhacen125 04-14 [Position/Number of discs] Front/Single disc [Goodness of fitment
It is not officially released by Manufacturer, but it fits the WR155.
Bessura's website lists VD-181JL as an official fit.
I think the Pad that fits the CRF250L will fit the WR.
Please do so at your own risk.View Detail
Fits: HONDA FTR250 86 /II [Application Areas/Number of Discs]Front/Single Disc [Compatibility]◎, HONDA FTR223 00-15 [Place of use/Number of discs]Front/Single disc [Compatibility]○ ○, HONDA CB223S 08-15 [Position/Number of discs]Front/Single disc [Goodness of fitment]◎, HONDA CB250RS 85 [part used/number of discs] Front/single disc [degree of fitment, SUZUKI SKYWAVE400 burgman 99 AN400X [part used]Rear [fitment]◎
[How is it used?
Used on FTR223.
Applications:Street riding, Touring, Circuit, FlatDirt
Was the one you received as per Image?
Just like the image. The base metal, gold, is also chic and nice.
The surface of the Brake Disc also had a semi-metallic feel to it, which seemed to work well.
Was the installation difficult?
The installation is not that difficult, and if you have enough time, it is very durable.
However, if the piston is sticking or is reluctant to move, it will take a bit of work.
When removing the pad pin or caliper mounting bolt, it is recommended that you use a good precision tool from a proper tool manufacturer if possible.
When you remove the Pad, you can push the entire Pad when you push the Piston back. (Skinning) This can be done easily by using
How was your experience with it?
Compared to the OEM, I think it worked better and had better control, and I was able to slow down enough on the circuit with my own kill at the time, and I didn't make the mistake of overrunning.
I was able to drive safely in the city and on a tour because it worked well and gave me plenty of room.
Life was longer and there was less aggression to the brake disc rotor.
Compared to DAYTONA's Red Pad, I felt it was slightly less effective and less controllable.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
As my own Skill rose, there were times when I wished it would work a little more.
(Points and hangs for installation/things you should prepare together)
As the installation point or hang, the
To reduce the squeal, chamfer the short side of the pad with an ironworking file.
Apply a thin layer of brake pad grease to the surfaces of the caliper and piston. (Base material) If you apply it on the whole side, Dust will not adhere well.
If the surface of the pad pin is covered with rust or dirt, I use about #400 water-resistance paper and inexpensive lubricant such as Kure 556, etc., and clean it with oil. Then apply a thin layer of pad grease and install.
Use a mild detergent and tooth brush to clean the caliper. Use a mild detergent and toothbrush to clean calipers. ・Parts cleaners that are less aggressive to rubbers should be used only where there is a lot of dirt. (Chain cleaner) Cleaned at
Spray the entire caliper with silicon spray and wipe it with a dustcloth. (Before installing the pad)
You may want to prepare the following items together
Pad grease
Lubricant for oil sharpening
Silicon spray
RubberGrease or Silicon grease (For piston cleaning and wringing out)
Parts cleaner (Chain cleaner)
Scraper (A leather skewer or slotted screwdriver is also acceptable.)
Iron Rasp
Water-resistance Paper
PistonPliers (PistonTool) (For piston cleaning and wringing out)
Pad pin (If the rust is severe and causing bumps)View Detail
Fits: SUZUKI GSR400 06-10 [part used]Rear [fitment]◎, SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA) 13-16 [part used]Rear [fitment]◎, SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA) 13-15 [part used]Rear [fitment]◎, SUZUKI GSX1300R GSX1300R HAYABUSA(GSX1300R HAYABUSA) 08-12 [part used]Rear [fitment]◎, SUZUKI GSX-R1000 07-08 K7/K8 [part used]Rear [fitment]◎
In my riding style, I only use the rear brake for speed adjustment, so I don't care if it works normally and has good control. So I thought this Pad is the right answer.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
通知
在您加入購物車前請選擇選項。
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.