【本體】
・額定電壓:dc12v
・外徑尺寸:w25.5mm×h30.5mm×d15.5mm(※突起部除外)
【構成部品】
・spi-110 c1本體×1
・車種専用線束×1
・各種雙面膠
・使用說明書
*是2018年6月型號的產品. 2019型基本上不適合除了符號項目。
* spil - 110c1 +專用線束的全套組件在標准齒輪的變速齒輪上注冊. 除了一些車型。
* spi-110c1單站移位位置未注冊。
*它將顯示除了齒輪包含保持運行離合器,但這不是故障。
*請注意,在前面不要粗心,在騎車時先考慮安全。
*在公共道路上使用時,請遵守交通規則和騎行。
*請不要使用沒有火花塞的電阻器. 請使用有電阻的火花塞,因為不使用火花塞電阻時可能會產生噪音,旋轉信號可能輸入不正確。
*請粘貼所附雙面膠帶,以免水進入,因為本產品背面有開關。
*請按照說明書正確安裝. 不這樣做可能會引起火災、故障等。
*安裝本產品後,請定期檢查是否有零件輸出。
*請注意,對於因使用本產品而造成的損壞、事故或其他損害,本產品概不負責。
*請注意,在維修過程中,保修部不會對解吸人工成本和其他各種費用承擔任何責任。
*由protec對應的所有車輛均為std車輛. 在配備其他品牌oem配件的車輛上也會出現這種情況。
*它對應於沒有在相應信息中列出的車輛. 所需零件見附件大表。
*安裝時,請務必檢查摩托車使用說明書中的每一條布線。
[Main unit]
・Rated voltage: DC12V
・Outer diameter dimension: W25.5mm x H30.5mm x D15.5mm (*excluding protruding parts)
[Component parts]
・SPI-110 C1 main unit x 1
・Model Specific Harness x 1
・Various double-sided tapes
・Instruction manual
2019 models are basically non-compliant except as noted.
*The full kit of SPI-110 C1 + harness is already registered for shift position in standard gear.Except for some models.
*Shift position is not registered for SPI-110 C1 by itself.
*When the clutch is depressed while driving, the display shows a gear other than the one in which the clutch is engaged, but this is not a malfunction.
*Prioritize safety while driving and do not be careless in front.
*Please do not use non-resistive spark plugs.If you use a plug without resistance, noise may be generated and the rotation signal may not be input correctly, so please use a spark plug with resistance.
*Please put the attached double-sided tape on the back side of this product to prevent water from entering because there is a switch.
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*After installing this product, periodically inspect it to see if any parts have fallen off.
*PROTEC is not responsible for any damage or accident caused by the use of this productProtec is not responsible for any damage caused by this product.
*Protec is not responsible for any labor charges for removal or other expenses incurred during repairProtec is not responsible for any damage caused by this product.
*PROTEC: Vehicles that have been tested by Protec are all stock.There is a possibility that a problem may occur if the vehicle is equipped with aftermarket parts other than stock parts.
*This product can be used for vehicles that are not listed in the compatibility information.Please refer to the list for the required parts.
*Please refer to the service manual of your motorcycle to confirm the respective wiring before installation.