【平穩驅動系統】
平穩驅動系統,針對不同類型的車制定最合適的套裝。
絕緣子帶、噴油螺栓、空氣凈化器箱、懸架等
靜止費被取消。它是一個放電的系統,使流體流動順暢。
平穩驅動系統不算是所謂的調校部件。
他們是把原來的問題解決的部分。
自豐田鋁帶公布以來,大眾已經意識到靜電的問題。
平穩驅動系統中的螺栓。螺母通過空氣放電(電暈放電)消除螺母鋸齒尖端的靜電。
靜電荷是正電荷或`-電荷的盈余。
這些條件總是發生在所有物質 "動 "的情況下。
有時會在瞬間中和或接地而失去。
最好在產生靜電的地方消除靜電。<可以通過移動靜態來刪除,但會影響沿途的一切。
靜電路徑中的懸浮物可能會影響運動。
在進氣系統中,它對外界空氣的 "導入 "流和混合空氣的 "流入 "流起到阻力作用。
所謂的 "砰砰 "現象可能是由於絕緣體的靜電荷導致混合氣不能順利進入發動機。
到了一定程度,進氣力失效,混合氣一下子進入,造成粘滯。
唐突也是一種時間差。如果沒有躲避,說明從初期就可以加速。
從早期階段開始的平穩加速意味着您可以達到目標速度,而無需比以往更多地打開油門。
行駛越平穩,駕駛越輕松,越安全,打開油門踏板的時間越少,行駛里程就越好。
越早加速,你的時間就會越好。這也是電摩車速度較快的主要原因。
絕緣子帶螺栓減速
更換原絕緣子帶螺栓即可!是。
使用橡膠絕緣子的內燃機一直在充電。
噴射器。至於化油器,它可以防止靜電在車體本身積聚,防止吹油的理想狀態。
只要空氣凈化器外殼和進氣管是塑料的,進氣口就不能帶電,無法順利吸氣。
光滑的感應(黑網)消除了機箱內的靜電。<對於不能安裝的部分,塗抹雙向塗層可以防止靜電產生。
[Smooth drivetrain]
Smooth Drive Systems has developed the most suitable set for each model.
Insulator band, injection bolt, air cleaner box, suspension, etc
This system eliminates and discharges the static electricity and makes the fluid pass through smoothly.
Smooth Drivetrain is not considered as a tuning part.
It is a part that brings the original problem to a solution.
Since the announcement of Toyota's aluminum tape, the general public has come to recognize that static electricity is a problem,
For more than 30 years, there have been various static electricity-related products for vehicle, but they have been repeatedly released and disappeared.
The bolts and nuts included in the Smooth Drivetrain eliminate static electricity by aerial discharge (corona discharge) from the serrated protrusions on the tips.
Static electricity is a state in which there is an excess of either + charge or - charge.
That state always occurs in every situation when matter "moves".
Rubbing, spinning, flowing, bending, temperature difference, but it can be neutralized instantly by +- or grounding and disappear.
It is best to remove static electricity at the point where it is generated.
Removing static electricity can be done by moving it, but it will affect everything along its path.
The suspension is in the path of static electricity and may be affected, resulting in poor movement.
In the intake system, it resists the introduction and flow of outside air and the inflow of the air mixture into the engine.
The so-called "thump" is probably caused by the static electricity of the insulator pulling the air mixture and preventing it from entering the engine smoothly.
If the static electricity of the insulator is removed and the air mixture enters gradually, the sticking will be less.
Thump also leads to a time lag.The lack of thump also means that you can accelerate early on.
The ability to accelerate smoothly from an early stage means that you can reach your target speed without having to open the accelerator more than before.
If you can drive smoothly, it is easy and safe, and if you open the accelerator pedal less, or open it less time, fuel consumption will naturally increase.
The earlier you can accelerate, the better your time will be.This is one of the main reasons why electric motor vehicle have better times.
The insulator band bolts are used to slow down the power of the insulator
Just replace the original insulator band bolts!It is.
Internal combustion engines that use rubber insulators are always electrically charged.
As for injectors and carburetors, it prevents static electricity from accumulating on the body itself and preventing the fuel from blowing ideally.
As long as the air cleaner case and intake pipe are made of plastic, the intake air will be charged and will not be smooth.
Smooth Induction (black static dissipative mesh) removes static electricity from the case.
For the parts of the case that cannot be installed, apply Two Way Coat to reduce static electricity generation.