【規格】
・額定電壓:DC12V
・消耗電力:遠光30W/近光30W
・LED:CREE公司製 XLamp XP-L LEDs
・色溫:3000K
需要使用原廠大燈(編號33120-maz-003)。
※根據使用說明書正確安裝設備。不正確的安裝將導致火災。它可能會導致故障。
※在安裝前,請務必取下電池負極側的端子線,並確認鑰匙已關閉。<請勿觸摸或玷污LED芯片。LED燈泡有一個帶密封圈的亞克力帽。拆除蓋子和密封圈後,因污染而造成的LED燈泡損壞不在保修范圍內。
※本產品為精密儀器,操作時應十分小心。不要摔倒或強行拉線。操作不當可能會造成故障、受傷或燒傷,並可能導致危及生命的事故。此外,要小心,因為火花和有缺陷的絕緣材料會引起故障和車輛火災。<本產品的拆解。不要對數據進行任何修改。分解:我們對改裝後的產品不提供任何保證。<不要直視大燈的LED燈。它可能會導致視覺障礙。<在關燈期間和關燈後,請勿將水濺到鏡頭上。溫度的突然變化可能會導致透鏡或LED燈泡的損壞。不要觸摸 "導閥體"、後風扇安裝架或控制器單元,因為它們可能會變熱。
※本產品僅供摩托車使用,不能用於四輪車。四輪車用產品單獨銷售。<請勿用紙或布覆蓋,也不要在易燃物附近點燃。它可能會引起火災或異常加熱。請勿在易燃物附近點燃,如易燃噴漆稀釋劑或其他可能點燃的易燃物。<請勿在點亮狀態下安裝大燈。否則可能導致故障或燒毀。
※本產品為日常使用的防水產品,但並非完全防水。用乙烯膠帶或自粘膠帶將控制器單元耦合器包起來,或用填縫劑防水。不要用超過必要的水潤濕它。
※用高壓清洗機洗車時,不要讓高壓清洗直接撞擊產品。<請勿跌落或強烈撞擊LED燈泡或控制單元。不僅會損害和降低性能,還可能造成傷害。
*當組裝LED燈泡時,請務必將附帶的硅脂塗抹在 "用戶手冊 "中的油脂標記處。<不要遮住防水扇。確保風扇後面有足夠的空間讓空氣流動。<使用螺紋鎖固劑,防止螺紋部位的松動。另外,請定期重新擰緊。
※安裝需要專業的知識和技能。請到指定的維修機構,由熟練的技師進行維修。
※使用前對准光軸。它可能會阻礙對向車輛的視線,造成交通事故。詳情請參考《道路車輛安全標准》。
*因使用本產品而引起的故障。因意外事故造成的損失,我們不承擔任何責任。此外,本公司不負責本產品的安裝、拆卸等維修費用。先謝謝你的理解。<在安裝或使用過程中,如果感覺到任何異常,請與 "protec服務部 "聯系。
[Specification]
・Rated voltage: DC12V
・Power consumption: Hi beam 30W / Lo beam 30W
・LED: CREE XLamp XP-L LEDs
・Color temperature: 3000K
*Stock headlight (No.33120-MAZ-003) is required.
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF.
*Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up.The LED bulb comes with an acrylic cap with a sealing seal.
*Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle.
*Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty.
*Do not look directly at the LED light when it is on.It can cause visual impairment.
*Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature.
*This product is for motorcycles only, so cannot be used on four-wheeled vehicles.This product is not for use on automobiles.
*Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite.
*Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns.
*This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary.
*When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product.
*Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury.
*When assembling the LED bulb, be sure to apply the supplied silicon grease to the areas indicated by the grease marks in the instruction manual.
*Do not cover up the waterproof fan.Make sure that there is enough space behind the fan for the sucked air to flow.
*Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended.
*Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics.
*Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*PROTEC is not responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair.
*If you feel any abnormality during installation or use, please contact PROTEC Service Department.