■高性能數字3g傳感器!
。這是一款適用於暢銷已久的防盜報警器的車模套件,即使是初學者也能輕松使用。
。不需要遙控器。您只需操作點火鑰匙的開/關,就可以輕松地停用該設置。
。當數字3g傳感器檢測到姿態變化超過5度時,系統會發出122db的報警聲。
。該車型套件的特點是包含了`sensor`指示燈LED的安裝位置和接線說明手冊。
。傳感器已經根據各車型調整到合適的長度,所以可以整齊地安裝,不用再進行不必要的長接線。
。警報器可以通過側面或中間的支架輕松設置在停車位置。
【安裝說明】
。拆下座椅和左側蓋板。<將cs-550m傳感器安裝在固定電池的支架上,將紅線連接到傳感器的正極,黑線連接到電池的負極。傳感器用雙面膠帶連接,但可以用 "捆綁帶 "固定,以防止其失靈。
。正面有一個紅色的橡膠罩,如果按照圖中所示把紅色的線穿過去,就可以很好的蓋住橡膠罩。
。揚聲器連接在左側蓋內的電池盒外側,並與`傳感器本身相連。
。從後擋泥板後面取下蓋子。黃圈有兩個螺絲,紅圈有兩個推鉚釘。如果你把它們都拆掉,蓋子就會脫落。
。圖中紅色圈出的半透明橡膠蓋內有一個尾燈的防水3p耦合器。配線是防水耦合器,有黑/綠/黃三根線,很容易辨認。
。將傳感器的橙色線與尾燈的黑色線用電擊方式連接。
。指示燈連接在油箱和頂橋之間的框架上。將`sheet`左側蓋板與傳感器的線連接後放回,工作完成。
。大約需要30-40分鍾的時間才能到達這個點。感應器和警報器的安裝位置在說明書中都有顯示,所以安裝起來非常方便。
【操作】
1)關閉鑰匙,停止發動機。
2)打開鑰匙,立即關閉。
3)聽到短促的蜂鳴聲,"指示器 "的紅燈閃爍0.5秒後熄滅2秒,然後重復動作。
4)現在設置報警。
在設定報警後的一分鍾內,即使檢測到異常也不會發出警報,但指示燈會快速閃爍。
當它在1分鍾後檢測到異常時,指示燈高速閃爍,警笛發出122db的巨大報警聲。
■High performance digital 3G sensor!
・This is a special kit for a long-selling burglar alarm that is easy to use even for beginners.
・No remote control required.The setting can be easily canceled only by operating the ignition key ON / OFF!
・The digital 3G sensor sounds a 122dB alarm when the vehicle's attitude changes by more than 5 degrees.
・The feature of the kit is that it comes with instructions on where to install the sensor, siren, and indicator LED, as well as instructions on how to connect the wires, so you can easily install it without worrying about the placement of each part, unlike universal kits.
・The wiring of the sensor itself has been adjusted to the appropriate length for the model of vehicle, so it can be installed neatly without unnecessary long wiring getting in the way.
・The alarm can be easily set on either the side stand or center stand.
[installation instructions]
・Remove the seat and the left side cover.
・Attach CS-550M sensor unit on the bracket holding the battery, and connect the red cord of the sensor unit to the positive side of the battery and the black cord to the negative side.The sensor body is attached with double-sided tape, but it is recommended to fix it with a bundle band to prevent malfunction.
・There is a red rubber cover on the plus side, so if you put the red cord through as shown in the image, you can cover the rubber cover nicely.
・The speaker is attached to the outer side of the battery case in the left side cover and connected to the sensor itself.
・Remove the cover from behind the rear fender.The yellow circles have two screw locations, and the red circles have two push rivets.Remove them all and the cover will come off.
・The waterproof 3P coupler of the taillight is located in the translucent rubber cover circled in red in the image.The wiring is a waterproof coupler with three wires (black, green, and green / yellow), so it should be easy to find.
・Connect the orange cord of the sensor to the black cord of the taillight with an electro tap.
・Attach the indicator light to the frame between the tank and the top bridge.Connect the cord of the sensor body, and put the seat and the left side cover back together to complete the work.
・It takes about 30-40 minutes to get here.The installation position of the sensor and siren is shown in the instruction manual, so it is very easy.
[operating instructions]
1) Stop the engine with the key OFF.
2) Turn the key ON and immediately turn it OFF.
3) A short beeping sound is heard, and the red indicator light shines for 0.5 seconds, then goes out for 2 seconds, and the operation is repeated.
4) The alarm is set.
The siren will not sound for about one minute after the alarm is set, even if it detects an abnormality, but the indicator lamp will flash at high speed.
When an abnormality is detected after one minute, the indicator lamp flashes rapidly and the siren emits a loud alarm sound of 122db.