*由於樞軸部分相當粗,請使用附帶的長樞軸。
* 不論是鼓式機構還是盤式機構,腳踏剎車機構都需要進行改裝。請注意,不管是鼓式還是盤式,腳剎機構都需要改裝。(詳細情況請參考以下說明)。
【安裝】
※請有經驗的人做摩托車維修的組裝工作。
※由於擺臂長度延長,`傳動鏈需要延長。
* 原裝軸不能使用。請使用附帶的長軸。
*原廠樞軸不能使用。請使用附帶的長軸。<傳動鏈的格數根據車況和前後鏈輪的不同而不同,所以G.M.T.不提供這方面的信息。
*各加長型的車輪所能安裝的直徑,根據所使用的輪胎的扁平度和車輪的寬度組合而不同。
※對於寬輪,我們將確認安裝到`5.5j。(因為是新產品,所以我們正在等待核實目前的情況。請諒解。)
*需要調整車輪和鏈線的中心位置,調整剎車相關部件的位置。
* 如果您的車架和搖臂之間的間隙超過0.5mm,請使用墊圈來減少間隙。<間隙超過0.5mm時,請使用墊圈減小間隙。
*騎行前請務必檢查後懸架是否有異常接觸點,即使後懸架處於全底狀態,也要檢查。
※每件產品的細節可能會有輕微的規格變化。
請注意,產品可能與介紹中的圖片略有不同,但我們會優先考慮實際產品。
※請注意開始運行後的所謂 "初始松動",並經常進行檢查,以免出現意外問題。保修不包括嚴重損害產品價值或功能的缺陷。
【購買須知】
*所有G.M.摩托產品均為定制件。
【注意】
所有G.M.Moto產品均為定制件,可能無法彈開和拆卸,或者需要調整和修改各個地方。
本產品不包含在運輸過程中可能出現的輕微劃痕、刮傷或輕微不規則的油漆或鍍層。
保修期內,不包括為車輛登記車牌號、辦理保險或因任何原因由客戶自行決定的任何其他維修工作的費用。
由於制造商的原因,產品規格可能會有所改變。請注意這一點。
Manufacturer: KEPSPEED
Country of origin :China
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*Please use the supplied long pivot shaft as the pivot section is quite thick.
*The foot brake mechanism needs to be modified regardless of the drum or disc mechanism. (For more details, please see the explanation below.)
[About the installation]
*Please make sure that the person with experience in motorcycle maintenance performs the assembly work.
*The drive chain needs to be extended due to the extended swingarm length.
※Stock axle shafts cannot be used.Please use the supplied long axle shafts.
*Also, the stock pivot shaft cannot be used.Please use the supplied long shaft.
*The number of tentioners of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
*The installable wheel diameter for each extension type varies depending on the combination of flatness and wheel width of the tire used.
*For wide wheels, GM-MOTO will confirm the installation of wheels upto 5.5J.(This is a new product and GM-MOTO is waiting for verification.)
*It is necessary to adjust the center position of the wheel, the chain line, and the position of the brake related parts.
*If the gap between the frame and the swingarm is more than 0.5mm on each side, please use washers to reduce the gap.
*If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.
*Even if the rear suspension is at full bottom, make sure to check for any abnormal contact points before riding.
※There may be some minor specification changes for each product.There may be some points that differ slightly from the introduction image.
※After the start of riding, pay attention to the occurrence of so-called initial loosening and perform frequent inspections to prevent unexpected problems.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.
※Please judge by yourself whether it can be installed or not referring to the size indication.
[Notes on purchase]
*All GM-MOTO products are custom parts.In some cases, it may not be possible to install it on the bike, or it may need to be adjusted or processed in various places.
*There may be changes in product specifications due to the manufacturer's reasons.
* Please note in advance that cancellation and/or return of this product cannot be accepted once the order has been placed.