*由於樞軸部分相當粗,請使用附帶的長樞軸。
* 不論是鼓式機構還是盤式機構,腳踏剎車機構都需要進行改裝。請注意,不管是鼓式還是盤式,腳剎機構都需要改裝。(詳細情況請參考以下說明)。<傳動鏈的格數因車況和前後鏈輪的不同而不同,所以G.M.摩托不提供這方面的信息。
*不能使用原廠軸,應使用頸長215mm以上(建議220mm)的m12長軸。
※如果你沒有,你可以選擇額外購買。
*原廠樞軸不能使用。請使用附帶的長軸。
※各加長型的可安裝輪徑根據輪胎的扁平度和輪寬的組合而不同。
※在防傾桿的情況下,不建議安裝在極端降低規格的車上。
*對於寬輪,我們會檢查安裝到4.0j。(因為是新產品,所以我們正在等待核實目前的情況。請諒解。)
*還需要調整車輪的中心位置、鏈線、剎車相關部件的位置。
*這些調整將根據您的車輛狀況和使用的其他部件而有所不同。
請注意,調整方式由客戶負責。
* 如果您的車架與擺臂之間的間隙超過0.5mm,請使用墊圈來減少間隙。如果您的車架與擺臂之間的間隙超過0.5mm,請使用墊圈來減小間隙。
※如果在間隙過大的情況下擰緊轉軸,擺臂會過載,最嚴重時可能會損壞。
* 組裝完成後,騎行前一定要檢查後懸架是否有異常接觸點,即使後懸架處於全底狀態。
※請注意開車後出現所謂的 "初松 "現象,並經常進行檢查,以免出現意外問題。
本產品不包含任何損害產品價值或功能的缺陷。
※請參照尺寸標示等,自行判斷是否可以安裝。
本產品不包含車輛行駛後所發生的任何問題。
所有G.M.Moto產品均為定制件。
這些都是定制的零件,可能無法彈上,也可能需要調整或修改各個地方。
本產品不包含在運輸過程中可能出現的輕微劃痕、刮傷或輕微不規則的油漆或鍍層。
保修期內,不包括為車輛登記車牌號、辦理保險或因任何原因由客戶自行決定的任何其他維修工作的費用。
由於制造商的原因,產品規格可能會有所改變。請注意這一點。
Manufacturer: KEPSPEED
Country of origin :China
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*Please use the supplied long pivot shaft as the pivot section is quite thick.
*The foot brake mechanism needs to be modified regardless of the drum or disc mechanism. (For more details, please see the explanation below.)
[About the installation]
*The drive chain needs to be extended due to the extended swingarm length.
*The number of tentioners of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
※Stock axle shafts cannot be used.Use an M12 long shaft with 230mm below head length.
*For those who don't have it, it can be purhcased as an option separately.
*Also, the stock pivot shaft cannot be used.Please use the supplied long shaft.
*The installable wheel diameter for each extension type varies depending on the combination of flatness and wheel width of the tire used.
*In case of Sway bar, GM-MOTO does not recommend to install it onto extremely low down vehicle.
*For wide wheels, GM-MOTO will confirm the installation of wheels upto 4.0J.(This is a new product and GM-MOTO is waiting for verification.)
*Also, it is necessary to adjust the center position of the wheel, the chain line, and the position of the brake related parts.
*These adjustments will vary depending on the condition of your vehicle and the relationship with other parts used.
※The customer is responsible for the adjustment method.
*If the gap between the frame and the swingarm is more than 0.5mm on each side, please use washers to reduce the gap.
*If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.
※After assembly is complete, be sure to check for any abnormal contact points before riding, even if the rear suspension is in the full bottom position.
※After the start of riding, pay attention to the occurrence of so-called initial loosening and perform frequent inspections to prevent unexpected problems.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.
※Please judge by yourself whether it can be installed or not referring to the size indication.
*All GM-MOTO products are custom parts.In some cases, it may not be possible to install it on the bike, or it may need to be adjusted or processed in various places.
*There may be changes in product specifications due to the manufacturer's reasons.
* Please note in advance that cancellation and/or return of this product cannot be accepted once the order has been placed.