不含燈體
額定電壓:DC12V
功率消耗:近光燈30瓦/近光燈30瓦
LED:Cree Xlamp xp-l LED
色溫:3000K
發光顏色:鹵素燈泡顏色
*ø180大燈h4燈泡規格需要單獨安裝。
*請注意,有些大燈規格可能不符合車輛檢查標准。
* 最大發光強度的測量是基於與lbh-k03/lbh-k04一起提供的前照燈。lhl-k03/lhl-k04可能由於結構問題而不符合標准值,這取決於要組合的外部前照燈。
*如果大燈箱的寬度較小,請使用市面上出售的ø8mm間隔圈。
請按照說明書的要求正確安裝產品。不正確的安裝可能導致火災或故障。
在安裝之前,請確保通過斷開電池負極上的端子線,使鑰匙關閉。
請不要觸摸或污染LED芯片,因為這可能導致熱量積聚並燒毀LED芯片。led燈泡上裝有一個帶密封圈的丙烯酸蓋。一旦蓋子和密封圈被拆除,任何由污垢造成的led燈泡的損壞都不在保修范圍內,應該小心處理。
本產品是一種精密儀器,應小心處理。請勿掉落產品或強行拉扯電線。不要掉落產品或強行拉扯電線,因為這可能導致損壞、受傷、燒傷或嚴重事故。火花、絕緣不良或短路也可能導致產品損壞或車內起火。
請不要以任何方式拆卸或修改本產品。不要試圖拆卸或修改產品,因為這將使保修失效。
當大燈開啟時,請不要直視大燈中的LED燈。這可能會造成視覺障礙。
在燈光開啟時或關閉後,不要將水倒在鏡頭上。不要在燈開着的時候或關閉後立即把水倒在鏡頭上,因為溫度的突然變化可能會導致鏡頭或LED燈泡的損壞。請不要觸摸LED燈泡本身,燈泡後面的風扇,或控制器單元,因為它們會變熱。
該產品僅適用於摩托車,不能用於四輪車。該產品僅適用於摩托車,不適合用於四輪車。
不要用紙或布覆蓋燈,不要在易燃物附近點燈。不要用紙或布覆蓋,也不要在易燃物附近點燃,因為這可能引起火災或異常加熱。不要在噴霧劑或稀釋劑等易燃或可燃材料附近點火。
當大燈開啟時,請勿連接到大燈。不這樣做可能導致故障或燒傷。
該產品在日常使用中是防水的,但不是完全防水。從控制器單元出來的耦合器應使用乙烯基膠帶、自粘性膠帶或填縫劑進行防水處理。請不要用水打濕產品,不要超過必要的限度。
用高壓清洗機洗車時,請不要讓高壓清洗機直接撞擊本產品。
請不要讓LED燈泡或控制器單元跌落,或使其受到強烈的沖擊。這不僅會損壞產品,降低其性能,縮短其壽命,而且還會造成傷害。
在組裝led燈泡時,請務必將提供的硅脂塗抹在說明書中標有硅脂的地方。
不要遮蓋防水風扇。確保風扇後面有足夠的空間讓吸來的空氣流動。
請使用螺紋鎖固劑以防止螺紋松動。使用螺絲鎖以防止螺絲松動,並定期擰緊。
安裝需要專業的知識和技能。安裝工作只能由合格的機械師在經批准的車間進行。
使用前請務必調整光軸。使用前一定要調整光軸,因為這可能會妨礙來往車輛的視線,造成交通事故。更多信息,請參考道路車輛的安全標准。
請注意,本產品的安裝可能使汽車制造商的保修失效。
對於使用本產品造成的任何損害,寶德不承擔任何責任。Pro-tech對使用該產品造成的任何損害不負責任。請提前了解這一點。
如果你在安裝或使用過程中遇到任何問題,請聯系你的經銷商或Protec服務部門。
請注意,由於制造商的原因,產品規格可能會有變化。請理解。
Without any lighting
Rated Voltage: DC12V
Power consumption: Hi beam 30W / Lo beam 30W
LED: CREE XLamp XP-L LEDs
Color Temperature: 3000K
Luminescence Color: halogen bulb color
*Φ180 headlight H4 bulb specification is required for installation.
*The maximum luminous intensity is measured by the headlight attached to LBH-K03 / LBH-K04.In the case of LHL-K01 / LHL-K02, some aftermarket headlights may not meet the standard value due to structural problems.
*If the width of the headlight case is too small, please use a commercially available Φ8mm spacer collar.
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF.
*Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up.The LED bulb comes with an acrylic cap with a sealing seal.
*Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle.
*Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty.
*Do not look directly at the LED light when it is on.It can cause visual impairment.
*Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature.
*This product is for motorcycles only, so cannot be used on four-wheeled vehicles.This product is not for use on automobiles.
*Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite.
*Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns.
*This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary.
*When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product.
*Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury.
*When assembling the LED bulb, be sure to apply the supplied silicon grease to the areas indicated by the grease marks in the instruction manual.
*Do not cover up the waterproof fan.Make sure that there is enough space behind the fan for the sucked air to flow.
*Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended.
*Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics.
*Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*PROTEC is not responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair.
*If you feel any abnormality during installation or use, please contact your dealer or PROTEC service department.
*There may be changes in product specifications due to the manufacturer's reasons.