First of all, it looks dirty for some reason. It was a messy finish.
It doesn't affect the use of things, but it does bother me.
The GSX-R125 that I installed has a mirror hall because the Handlebar is a common part with the GSX-S125. I installed it there.
Installation is just finger screwing, so I'm worried about losing it.
I would like to be able to tighten it with a tool.
Fits: HONDA CBR150R 17, HONDA CBR250R 17, KAWASAKI Ninja250 17, YAMAHA YZF-R3 , HONDA CBR400R 17
[How is it used?
When considered as a single product, the longest is less than 5 years, or about 60,000 km.
Drive in Touring or Circuit.
The mirror holder for NISSIN's brake master (YZF-R25, CBR-250RR), CF-POSH Universal mirror holder, YAMAHA 5YU-26393-00, and many others.
The Ram Mount is used in combination with a short arm and a smartphone holder to hold heavy objects such as an iPhone 12 mini, Xperia 5, Galaxy S21, and Driveman BS- 8.
Was the one you received as per Image?
In the Instruction Manual, there is a piece of Pole Rubber stuck to the base of the ball, and for better or worse, it's just like the Image.
Was the installation difficult?
Since the entire circumference is round and there is no flat surface to apply a tool to, the bolts can be installed with a right hand turn, but it may require some ingenuity to tighten them.
It may be possible to use a Clamp or a Monkey Wrench to hold it in place, but I'm using a Dustcloth wrapped in leather gloves to hold it in place, and then screwing it into the screw lock with all the screws dipped in it.
How was your experience with it?
There were no problems such as the ball falling out of the Bolt, the aluminum body cracking, loosening, or the Arm coming off, and the mounted devices are working fine.
[Included Parts:were they on?
Although it says that the screw lock is required, I'm pretty sure it isn't, so you'll need to prepare for it.
[Was there anything that disappointed you?
Nothing special. If you go to the store, you can see it, but it looks like Ram Mount, for better or worse.
It's an M10 1.25 Normal Thread Screw, which is the same bolt size as most Mirror holders, so it should be easy to install.
However, because the screw part itself is not that long, and because it is aluminum, and because it is difficult to remove, it is not good for tightening together.
On the other hand, since it has to be installed using the screw lock without any tools, it is better to think that it is difficult to remove it. I tried to remove it by squeezing it under the same conditions as when I installed it, but it didn't seem to budge.
It competes with Quad Rock and SYGN HOUSE, and as a product, it has lost quite a bit in terms of its beautiful appearance, but I have yet to encounter any irritating or critical aspects in practical use.View Detail
Fits: HONDA CBR150R 17, HONDA CBR250R 17, KAWASAKI Ninja250 17, YAMAHA YZF-R3 , HONDA CBR400R 17
It is convenient because the Mount base for RAM can be added to the Screw hole of M10.
You can't hang a tool on it so you need to grab it with ArmParts and tighten it.
I've never had it come loose while driving by just grabbing it with the Arm and turning it.
It's not Firmly tightened, so I hope they improve it.View Detail
Fits: HONDA CBR150R 17, HONDA CBR250R 17, KAWASAKI Ninja250 17, YAMAHA YZF-R3 , HONDA CBR400R 17
If you use Mirror's hole or an empty Screw hole, it's not usually noticeable.
The Spanner groove is also left uncut and round, so you may need to be a little creative to install it.
And the build is rough.View Detail
Fits: HONDA CBR150R 17, HONDA CBR250R 17, KAWASAKI Ninja250 17, YAMAHA YZF-R3 , HONDA CBR400R 17
I took advantage of the hole in the vehicle's body and installed it for the GoProMount.
You can install it in any position to enjoy powerful images easily!View Detail
Fits: HONDA CBR150R 17, HONDA CBR250R 17, KAWASAKI Ninja250 17, YAMAHA YZF-R3 , HONDA CBR400R 17
When I arrived, I was surprised to see that his appearance is different from the photo. It's dirty, to say the least.
It became the appearance of the picture if it was processed by Paper processing for the first time from File hanging and polished by PIKAL.
The problem with this is that the smartphone holder cannot be tightened with a tool even though it has 10mm screw, and even if it is tightened with a finger, the smartphone holder starts to turn by vibration. It will fall off before it is stolen.
The solution is either machining it so that it can be turned with a tool or gluing it in place that won't come off forever. I'm the former.
I recommend it because it makes effective use of the Mirror Hall, which was only blocked up until now.
processing plan
? I'm going to punch a hole in it like I did.
Because the diameter of the root of the screw has become Large, shave 2 sides with File so that the Spanner may enter.
Firmly grab and turn it with ?Pliers. You need to be prepared to get a lot of scratches on the shaft.
? Solidify with high strength screw lock agent
View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING