761.09 HKD
(14,720 日元)
4 (27 評論)
Very Good
Price suitableI bought it to measure Time at a driving session.
I used it in Tsukuba and Mogi, and it worked fine.
The installation is bracketed to Under Cowl.
It's easy to install, so if you want to measure Time for now, this is a good introduction.
I haven't compared it to the others, so I don't really know, but it feels like the battery drains faster.
Reviews For CLEVER LIGHT ZiiX Lap Timer 計時器 From Other Webike User
Very Good
Compatible with most CircuitsWhen I went to run Circuit a few times, I became curious about how many seconds I was running and bought one.
The installation is easy if you are familiar with the electrical system.
The only thing that bothers me is the location of the Sensor.
Depending on the Motorcycle, it is very difficult to decide where to put the Sensor.
In the Racer's Under Cowl, the Sensor is deformed by the heat of the Exhaust System, so a little ingenuity is required.
It is very useful because it is easy to know the time.View Detail
Average
Enough for an introductionMotive for purchasing
I bought it to check the time while driving in the Circuit At first, it was good enough for me to know the time, so I used Cue Stars and Dig High technologyLap timers of GPType S, such as spice, have a high The cheapest magnetic type is the LeverLight Lap I decided to try the timer
About the product
The numbers are large and the visibility is good
The information displayed is only the time of the lap, so you can't compare it with other laps while driving Even so, the numbers are still large enough to be visible while driving I think that this is an excellent costumer for those who only need to know the lap time anyway
Connect to the Battery and you don't need batteries
Lap timerBody starts with the Button battery, but it connects to the attached Battery You can use the Wiring function without the Button battery There is a switch to turn on/off the power, but be careful not to leave it on and leave the battery on Let's
Limited to Circuit with embedded porcelain bars
The included magnetic sensor detects and wraps the magnetic bars embedded in the Circuit Unlike GPS, the accuracy is measured by magnetic transit timing, so the accuracy is relatively high (Depending on the position of the Sensor, it may pick up Noise.) But, on the other hand, you can't measure a lap without a porcelain bar, so I'm going to have to get the Circuit running well before I buy it You need to make sure that the porcelain bars are embedded
It's a bit of a hassle to install
The key is the magnetic sensor, but if you are not careful about the position of the magnetic sensor, it will not detect magnetism and will not be able to correctly wrap the lap It cannot be measured Also [Contents] does not even come with a bracket to attach the Sensor to the vehicle by yourself You need to prepare a Bracket to match, and the Lap timerBody is also fine Large size, Quantity:I'm also very careful about the position to setView Detail
Very Good
Although it is limited to the Circuit buried in magnetic bars, I bought it because of its ease of use and cost
What made you decide to buy?
I rejected the GPS-based QSTARZ and Dig spice because they are too expensive at $60,000-$40,000
The frequently driven Circuit is compatible with magnetic sensors, and it was affordable Choice
How was your experience with it?
The results of using it at three locations in the manual's "Magnetic Bar Buried Circuit List"of the instructions
Okegawa Sports Land…15cm of ground clearance is OK
However, the magnetic bar does not pass through 50 to 60cm from the end of the courseLeft, so it will not react Mm (A magnetic bar is buried a few meters from the ControlLine.)
Quick hanyu & hellip;12cm of ground clearance is not enough
They were buried a long time ago and they hardly responded
If you set up the SS at 9 cm above ground level, 80% of the time it responds, but there are many malfunctions
Tsukuba 1000…ground clearance of 18cm is OK
Only one lap of the 45 minutes was unresponsive
Was it difficult to install? (In the case of hard parts)
Be careful with the handling and fixing of Wiring to avoid the high temperature of the Exhaust pipe etc I did
Now you need some DIY skills on the Sensor side Bracket
What is the point or hang of installation (for hard parts)?
It's difficult to connect the power supply to ACC, so it's connected directly to the Battery
(After all, it's non-Waterproof, and it's removed except when running Circuit, so Large It's tough:)
The magnetic sensor is installed on the center line of the straight line with a ground clearance of about 10 cm or less in the Rider's riding condition Then it's best
How does it feel when you wear it and what is your height, weight, etc. (in the case of Apparel)? Any
[Was there anything that disappointed you?
The connector is thin and not very durable
Do you have any wishes or improvements you would like to make for the Manufacturer?
Waterproof Specification of the body
Strengthened connector part
[Do you have any products to compare it to?
The company's TimeA Tucker
[Others]
The magnetic sensor bracket is not included, so this is a DIY project
It's even better if you can use the butterfly screw to adjust the ground clearance
The magnetic sensor is covered with a plastic bag to prevent wounds and stains WaterproofView Detail
Very Good
goodPurchase required for traveling Circuit. I am satisfied with the function I was looking for! I would like to improve about the point that there is no Waterproof function to Body although it has the Waterproof function of Sensor part!View Detail
Very Good
Cost performance is goodI purchased this product because it seems that the magnetic bar is buried in the Course that I always run and the Red external Timer seems to forget the Red outside line unit.
Easy to buy in terms of price, the function is also simple and easy to use, easy to see the Large size of the display part, it is good with the Large size which is not troubled by the installation place.
However, as far as magnetic Sensor is concerned, it will not pick up magnetism unless it is in a rather low position.
View Detail
Most Viewed Reviews Of CLEVER LIGHT Lap Timer
Excellent
It is encouraging.after all is said and done "I know my current situation, my status on the day, and my Levels." That's a good idea!
No pressure ≒ fall Risk reduction ⇒ long and enjoyable". That would be the case.
I am not aiming for Time in the dark, but it is nice to know the Level as a concrete number.
Especially AttackIndicator is a sectional Best; Green Light 、 Less than that; Red. It is very encouraging because it is displayed each time at the
I am not good at working, so I asked Shop to do the installation.
The power supply is taken from Battery, but the Instruction Manual for handling "Battery may rise and should be disconnected when not in use." and it is necessary to disconnect the Body's connecting wires (3 wires) except when driving. (This is not a hassle and I don't feel it is a minus point). (This is not a hassle and I do not feel it is a minus point.
Another thing to keep in mind is that 'Protect them from the sun when they are at rest.' This means.
It is not a problem in light sunlight, but if the TimeaTuckerBody is exposed to strong sunlight and heats up too much, the LCD Panel will not display. This has been confirmed by contacting the Manufacturer. Therefore, I cover the body with a Towel during intervals in the Circuit on days with strong sunlight.
I am very satisfied with the performance of the product and highly recommend it!
What's strange about the Circuit run is that Sometimes you get your best time when you think you're playing along." I guess that's what you mean! LOL.View Detail
Excellent
I can recommend it.I think it's a good product
This kind of lap timer is essential for those who run Circuit.
Cost performance is the best.
We are using it at Tsukuba Circuit without any problems.
I used to use LAP SH**T, but it had reached the end of its life, so I replaced it. In terms of appearance, I feel that this product is somewhat more robust, with thicker sensor wires, etc.
I was concerned that the angle dependence of the LCD contrast is large, making it difficult to check the time while driving, depending on the angle at which it is mounted. If the dial is angled too far away from the front, the letters will become faded.View Detail
Very Good
Mounting positionInstalled on GSX-R125 at Circuit Running.
I had a hard time finding a place to install the Sensor. I tried to install it around the Rear Suspension Link, but I am not sure if it will respond.
The thickness of the body is not so bad, so the installation space around the meter is also limited.
As others have commented, the included Magic tape is weak and insufficient, so I recommend buying it.
Convenient because it's rechargeable, and I'm satisfied with the price.View Detail
Very Good
Compatible with most CircuitsWhen I went to run Circuit a few times, I became curious about how many seconds I was running and bought one.
The installation is easy if you are familiar with the electrical system.
The only thing that bothers me is the location of the Sensor.
Depending on the Motorcycle, it is very difficult to decide where to put the Sensor.
In the Racer's Under Cowl, the Sensor is deformed by the heat of the Exhaust System, so a little ingenuity is required.
It is very useful because it is easy to know the time.View Detail
Very Good
Pay attention to the magnetic sensor mounting position and direct sunlightFirst of all, the installation position of the Magnetic Sensor is troubling.
In the case of the Race car, I think it has a tight Under Cowl, so the installation position is quite restricted.
I have it over the Under Cowl around where the Side Stand was originally attached, but sometimes it misreacts …
It would be nice if the manufacturer could provide some installation examples.
Also, it stops working in direct sunlight in summer, or maybe it malfunctions? Or rather, it malfunctions?
Keep them in the shade when they are stopped.
If it's running, the wind may cool it down, but I've never had it go wrong.
Also, if you take the power supply directly from the battery, the battery will rise even if the power supply is off.
It is necessary to build a Relay or to remove the power Coupler each time (the instruction manual notes the latter).
I just bought a Lithium ion battery and the voltage was like 2V and I was shaking.
It is a mystery why there is so much dark current when it can be turned on and off.View Detail
Other Reviews From Japanese Webike user
Excellent
Radipon handled in Mild?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
Very Good
packtalk bold Attached MountI purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Excellent
Grip replacementGrip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
Very Good
Works well in everyday life[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING