* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
We use cookies to provide and improve our services. By using our site, you consent to our Privacy Policy including cookie. Learn more
I installed it on the CRF 250 M of MD 44, but Adjuster should be fixed with Tape etc. at the time of installation. When I tightened with Torque44Nm prescribed without noticing that I misaligned at the time of tightening, how swollens are !! (It is as shown in the picture) I broke the protrusions on the body side and broke the 20,000 LINK to par, but I could install it again. I thought using it, I wanted to lower the adjustment by 10 mm more, I was more rough and I did not need fine adjustment within 25 mm. If fine adjustment is unnecessary 5000 yen cheap Adjustment of Zeta None VERSION is good? But it is cool so it was good.
OEMArm is actually looking Aluminum and it is surprisingly heavy with casting removed First I am surprised by the lightweight feeling of the real aluminum. Because Adjustable Dial is easy to fall, Recommendation is to temporarily fix the end with Masking tape. As the weight will be reduced under Spring, the suspension movement improves Response I feel like contributing to the Throttle response on Flat Galle Road. I am 2 cm protrusion of Front fork and I like it very much that it can realize Lowdown according to it. Although the Spring rate is decreasing due to the Lever ratio, I feel that ride quality is improving, I also like the movement of supple Arm. Because it is a part that looks firm while stopping, Arm of Red alumite meets ownership feeling and you can see it when you see it finely AdjustableMemory is also CUTE with Me Snap C feeling full mark..View Detail
Fork was pushed out to the limit, Rear was shortened to the limit at the ride height adjustment section, and even with -20mmSeat of db’s, it was quite Limit for 149cm to ride, but LINK was also Quantity at the lowest state.:Set and it gave me a little more room, so if you're worried about footing, I'd recommend it! However, if you lower it that far, the Side Stand will be too long and the Motorcycle will stand upright, so the recommendation is to use a STANDCut or ZETA aluminum side stand with a -15mm tip!View Detail
I use it for KTM, but OEM PowerParts has a Rear shock RoseStripes, this is a Spring-less, jig and press, Jacketc. If Shock is pushed in with a jig, PRESS and Jacketc It is impossible for the amateur After installation, it lowers 30mm. it is necessary to replace with Front and Rear Set The original suspension performance, the extension side was affected a little, well, this is how it isView Detail
The design is good and the product is as expected? (^-^) /? I recommend it to everyone I bought it to improve its footprint, and I'm sure it will achieve its purpose and give you peace of mind from now on You can driveView Detail
I bought them to improve my footing and I'm happy with the Potential as I expected Before, he was seated in Seat with his feet in a very splayed out position, but his feet are just his toes It's on the ground, so you can enjoy driving in peace? (^-^) /?View Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING